Metropower Portal | ||
| ||
DJ Wilma's 1275GT Clubman 1.8 K series Turbo Moderators: Jump to page : 1 2 3 Now viewing page 2 [25 messages per page] | |
Gallery-> Non Metro gallery | Message format |
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | sikguy - 19/3/2012 8:46 AM offfffffffttttttt 1.4 16v spi im drulling want one sooooo bad Engine is for sale ! | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | Took the engine out today and cleaned the engine bay out R65U wants to be changed to a PG1 with torsen, but as yet havent found one. Should have the front back to metal soon clean up the crap welding and get it sprayed so i can fit the engine Need to change the SPI tank fuel pump to the VVC one i took out the tro, feed some pipes front to back and hook up the front brakes before the engine fitting Going to take the 185 55 13 Toyo road pros off the GTA wheels and fit them to my MPI's for the metro Need ideas on what wheels to fit so it doesnt look like a mini on metro wheels. Will run 175 50 13's too (IMAG0068 [800x600].jpg) (IMAG0069 [800x600].jpg) Attachments ---------------- IMAG0068 [800x600].jpg (60KB - 75 downloads) IMAG0069 [800x600].jpg (58KB - 76 downloads) | ||
DAVESEI |
| ||
previously known as....Dazgta Posts: 2019 Location: birmingham | dytes,comp mo's, or go wide steelies | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | DAVESEI - 22/3/2012 9:07 PM dytes,comp mo's, or go wide steelies steelies purchased from the magic shed in Andover, known as Itsonlyme with 185 55 13 dunlops......185 55 13's roadpros from the cross spokes going on my tro handled so so much better on the 55 profile All i need now is a PG1 from a 620 TI with a type B, freelander flywheel and we are go for engine install.....once cheeky scott has got the front sorted Edited by djwilma 23/3/2012 1:12 PM | ||
Roverdose |
| ||
Veteran Posts: 444 | love it. prefer the look of the clubman's too. Drew | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | Roverdose - 23/3/2012 1:29 AM love it. prefer the look of the clubman's too. Drew good we have another clubman that needs saving, 1608cc k series turbo | ||
FreddieS |
| ||
Elf eating dog breeder Posts: 10531 Location: Guildford | Love it, when this is done i'll definatly have to swing by and have a ganders when im down your way! | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | FreddieS - 23/3/2012 5:18 AM Love it, when this is done i'll definatly have to swing by and have a ganders when im down your way! if i had a pound for everytime you said that i would be £2 richer Anytime, door is always open | ||
Danb1991 |
| ||
Extreme Veteran Posts: 543 Location: ashford/kent | are you joking about putting the 160 engine in this mini? that cant be safe you could just make it 1.8Turbo either way its gunna be dangerously quick lol | ||
minimunky |
| ||
Extreme Veteran Posts: 560 Location: sunny somerset | Minis love the ponys, vvc motor will be sweet in one, space up front is limmited, so turbos are a pain to squeeze in but can be done | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | Few things changed, i bought a PG1 with a torsen diff so going to change out the R65U as the car will be tracked and looking at 1/4 mile times the diff cars are 0.5 quicker in the late 13s Also removed the cross spoke alloys and stole the near new Toyo Roadpro 185 55 13s and put them on the metro So had to fit my Avon ZZRs which look ok, my mate says it looks like a mini on a metro chassis but will collect steelies from Tony Itsonlyme on thursday, along with MGF Calipers, carriers, 160 6 bolt manifold and MGF shafts for the PG1. I have some spare discs and pads (chocolate green stuff) for the time being Spacers on the back look er fooking big Subframe is new with braided lines for the brakes adjustable spax too (IMAG0086 [800x600].jpg) (IMAG0087 [800x600].jpg) (IMAG0089 [800x600].jpg) (IMAG0090 [800x600].jpg) (IMAG0091 [800x600].jpg) (IMAG0092 [800x600].jpg) Attachments ---------------- IMAG0086 [800x600].jpg (75KB - 80 downloads) IMAG0087 [800x600].jpg (57KB - 73 downloads) IMAG0089 [800x600].jpg (75KB - 73 downloads) IMAG0090 [800x600].jpg (73KB - 72 downloads) IMAG0091 [800x600].jpg (59KB - 73 downloads) IMAG0092 [800x600].jpg (98KB - 69 downloads) | ||
glyn-ellis |
| ||
Elite Veteran Posts: 697 Location: leigh | Them spacers look like they destroy wheel bearings! You can get some that in behind the stub axle but i can't remember where | ||
mini-mad-craig |
| ||
Elite Veteran Posts: 978 Location: Walderslade, Kent | Not trying to shit on your build but to me it just aint right mate a mates vvc mini on mini wheels... and again on metro wheels.. Not sure on what you're planning with this build but surely its worth looking into making Mini PCD wheels fit? Edited by mini-mad-craig 28/3/2012 2:42 AM | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | mini-mad-craig - 27/3/2012 10:41 AM Not trying to shit on your build but to me it just aint right mate Glad you read the thread ! Car will have wide steelies and 175 50 13s, mpi alloys are just on as a temp measure Why do the mini boys have kittens when you mention metro wheels | ||
mini-mad-craig |
| ||
Elite Veteran Posts: 978 Location: Walderslade, Kent | djwilma - 28/3/2012 7:46 AM mini-mad-craig - 27/3/2012 10:41 AM Not trying to shit on your build but to me it just aint right mate Glad you read the thread ! Car will have wide steelies and 175 50 13s, mpi alloys are just on as a temp measure Why do the mini boys have kittens when you mention metro wheels Just seen that.. on the PC now rather than the phone which only wanted to load up to the post where you said 'Need ideas on what wheels to fit so it doesnt look like a mini on metro wheels. Will run 175 50 13's too' Excited to see how it go's mate, should look prettty good on them!! | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | Few things have happened since last thread, got some wide steelies and vented discs, pads (ebc green chocolate) and calipers from the magic shed known as its only me. Need some spaces for the front wheels though as they do touch.... And Cheeky Scott has done a little welding, on the scuttle panel and filled in the holes on the bulkhead Have a C6BST with type b and an unknown K series PG1 with new bearings on its way to Matt P for refurb, so will be going PG1 (IMAG0096 [800x600].jpg) (IMAG0097 [800x600].jpg) (IMAG0098 [800x600].jpg) (IMAG0100 [800x600].jpg) (IMAG0112 [800x600].jpg) (IMAG0114 [800x600].jpg) Attachments ---------------- IMAG0096 [800x600].jpg (66KB - 76 downloads) IMAG0097 [800x600].jpg (60KB - 77 downloads) IMAG0098 [800x600].jpg (96KB - 74 downloads) IMAG0100 [800x600].jpg (48KB - 75 downloads) IMAG0112 [800x600].jpg (89KB - 76 downloads) IMAG0114 [800x600].jpg (93KB - 75 downloads) | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | Oh well looks like a trip to Santa Pod and being beaten by Sean has made me realise my mini needs a turbo ! So we have bought a 75 Turbo with a blown head gasket, will be getting the help of the ever helpful itsonlyme to strip the engine have a loom and ecu from Dazz and Sean and will be shooting for the same 200bhp K7 box from the Metro will be used, as mini has much smaller tyres and will have a type A diff from the 820 turbo box i just bought ! Will get pics up soon | ||
R100_vvc |
| ||
Expert Posts: 2029 Location: sittingbourne, kent | i bet that will be a tight squeeze, what sort of intercooling you gonna use? | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | R100_vvc - 28/4/2012 6:30 PM i bet that will be a tight squeeze, what sort of intercooling you gonna use? 1.8 goes in no problems so only issue is the turbo, which can be made to fit Have no idea on intercooling, looking at std 75 turbo intercooler but will see what we can do Only 200bhp (at the moment as may forged and for 250bhp) so possibly the std 75 or 220 turbo......will get something to fit once we decide on how to fit everything........ | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | Not much has been done as manic busy at work but collected the 75 1.8 Turbo which is now at itsonlyme's having the HGF fixed Should have the engine soon, can then bolt it in and have a Zandf remapped ecu and loom from Dazz and Sean to fit so should be close to the 200bhp mark once the 2 1/4" exhaust has been made Also had a new pedal made to go around the steering column Had a K7 gearbox made up by Matt Parker with a Type B that needs to be collected and will be using the metro flywheel and 220 turbo clutch Also got some 175 50 13 A539 yokos for £150 which are basically brand new...... (IMAG0144 [800x600].jpg) (IMAG0212 [800x600].jpg) (IMAG0213 [800x600].jpg) (IMAG0215 [800x600].jpg) Attachments ---------------- IMAG0144 [800x600].jpg (56KB - 78 downloads) IMAG0212 [800x600].jpg (59KB - 74 downloads) IMAG0213 [800x600].jpg (78KB - 73 downloads) IMAG0215 [800x600].jpg (59KB - 78 downloads) | ||
ding |
| ||
I'm still waiting for my commission for finding you the 75 | |||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | ding - 13/5/2012 9:27 PM I'm still waiting for my commission for finding you the 75 you know me, thats all the commission you will ever need | ||
munday |
| ||
Expert Posts: 5629 Location: Letchworth/Basildon | 2 1/4" exh makes me weep! | ||
djwilma |
| ||
Expert Posts: 2812 Location: Bournemouth | munday - 14/5/2012 6:12 PM 2 1/4" exh makes me weep! oops typo 2 1/2".......not that stupid on a turbo | ||
Mutts |
| ||
Lotus powered R100 MP Admin Location: Torbay, South Devon, UK | Have you got a couple of these yellow things handy.. I think you'll need em | ||
Jump to page : 1 2 3 Now viewing page 2 [25 messages per page] |
Printer friendly version E-mail a link to this thread Jump to forum : |
(Delete all cookies set by this site) | |
Running MegaBBS ASP Forum Software v2.0 © 2003 PD9 Software | |